GPIO_InitTypeDef GPIO_InitStructure2;

TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;

TIM_OCInitTypeDef TIM_OCInitStructure;

TIM_BDTRInitTypeDef TIM_BDTRInitStructure;

//第一步：配置時鐘

RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOB|RCC_APB2Periph_TIM1,ENABLE);

//第二步，配置goio口

GPIO_InitStructure2.GPIO_Pin=GPIO_Pin_8;

GPIO_InitStructure2.GPIO_Speed=GPIO_Speed_50MHz;

GPIO_InitStructure2.GPIO_Mode=GPIO_Mode_AF_PP; //設置為復用浮空輸出

GPIO_Init(GPIOA,&GPIO_InitStructure2);

GPIO_InitStructure2.GPIO_Pin=GPIO_Pin_13;

GPIO_InitStructure2.GPIO_Speed=GPIO_Speed_50MHz;

GPIO_InitStructure2.GPIO_Mode=GPIO_Mode_AF_PP; //設置為復用浮空輸出

GPIO_Init(GPIOB,&GPIO_InitStructure2);

//第三步，定時器基本配置

TIM_TimeBaseStructure.TIM_Period=1000-1; // 自動重裝載寄存器的值

TIM_TimeBaseStructure.TIM_Prescaler=72-1; // 時鐘預分頻數

TIM_TimeBaseStructure.TIM_ClockDivision=TIM_CKD_DIV1; // 采樣分頻

TIM_TimeBaseStructure.TIM_CounterMode=TIM_CounterMode_Up; //向上計數

TIM_TimeBaseStructure.TIM_RepetitionCounter=0; //重復寄存器，用于自動更新pwm占空比

TIM_TimeBaseInit(TIM1, &TIM_TimeBaseStructure);

//第四步pwm輸出配置

TIM_OCInitStructure.TIM_OCMode=TIM_OCMode_PWM2; //設置為pwm1輸出模式

TIM_OCInitStructure.TIM_Pulse=500; //設置占空比時間

TIM_OCInitStructure.TIM_OCPolarity=TIM_OCPolarity_Low; //設置輸出極性

TIM_OCInitStructure.TIM_OutputState=TIM_OutputState_Enable; //使能該通道輸出

//下面幾個參數是高級定時器才會用到，通用定時器不用配置

TIM_OCInitStructure.TIM_OCNPolarity=TIM_OCNPolarity_High; //設置互補端輸出極性

TIM_OCInitStructure.TIM_OutputNState=TIM_OutputNState_Enable;//使能互補端輸出

TIM_OCInitStructure.TIM_OCIdleState=TIM_OCIdleState_Reset; //死區后輸出狀態

TIM_OCInitStructure.TIM_OCNIdleState=TIM_OCNIdleState_Reset;//死區后互補端輸出狀態

TIM_OC1Init(TIM1,&TIM_OCInitStructure); //按照指定參數初始化

//第五步，死區和剎車功能配置，高級定時器才有的，通用定時器不用配置

TIM_BDTRInitStructure.TIM_OSSRState = TIM_OSSRState_Disable;//運行模式下輸出

TIM_BDTRInitStructure.TIM_OSSIState = TIM_OSSIState_Disable;//空閑模式下輸出選擇

TIM_BDTRInitStructure.TIM_LOCKLevel = TIM_LOCKLevel_OFF; //鎖定設置

TIM_BDTRInitStructure.TIM_DeadTime = 0x90; //死區時間設置

TIM_BDTRInitStructure.TIM_Break = TIM_Break_Disable; //剎車功能使能

TIM_BDTRInitStructure.TIM_BreakPolarity = TIM_BreakPolarity_High;//剎車輸入極性

TIM_BDTRInitStructure.TIM_AutomaticOutput = TIM_AutomaticOutput_Enable;//自動輸出使能

TIM_BDTRConfig(TIM1,&TIM_BDTRInitStructure);

//第六步，使能端的打開

TIM_OC1PreloadConfig(TIM1, TIM_OCPreload_Enable); //使能TIMx在CCR1上的預裝載寄存器

TIM_ARRPreloadConfig(TIM1, ENABLE); //使能TIMx在ARR上的預裝載寄存器

TIM_Cmd(TIM1,ENABLE); //打開TIM2

//下面這句是高級定時器才有的，輸出pwm必須打開

TIM_CtrlPWMOutputs(TIM1, ENABLE); //pwm輸出使能，一定要記得打開

// 在運行當中想要改變pwm的頻率和占空比調用：

TIM_SetAutoreload(TIM1,1000);

TIM_SetCompare1(TIM1,500);